Difference between revisions of "Original fold down saloon table"
(7 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
The early Konsorts had a folding saloon table which folded flat against the saloon bulkhead. This allowed for a pull bed frame which could be made up into a double berth with the port side cushions. | The early Konsorts had a folding saloon table which folded flat against the saloon bulkhead. This allowed for a pull bed frame which could be made up into a double berth with the port side cushions. | ||
− | [[File:kt_saloon1.jpg]] | + | [[File:kt_saloon1.jpg|600px|left]] |
− | [[File:kt_saloon2.jpg]] | + | [[File:kt_saloon2.jpg|600px|left]] |
− | [[File:kt_saloon3.jpg]] | + | [[File:kt_saloon3.jpg|600px|left]] |
− | [[File:kt_saloon4.jpg]] | + | [[File:kt_saloon4.jpg|600px|left]] |
+ | |||
+ | |||
+ | '''Measurements in millimeters''' | ||
+ | |||
+ | Bulkhead fixing: | ||
+ | 445 X 55 x 55 with an 24 X 18mm rebate on one edge to accommodate the bottom leaf. | ||
+ | This piece of wood is attached to the saloon bulkhead by 3 bolts which go through to the heads. | ||
+ | |||
+ | Bottom Leaf: | ||
+ | 1094 X 445 X 18. Sapele faced Plywood. This is attached to the bulkhead fixing by 2 chunky brass hinges. | ||
+ | These are rebated into both pieces of wood for a flush finish. | ||
+ | |||
+ | Top Leaf: | ||
+ | 1070 X 445 X 18 Sapele faced plywood. This is attached to the bottom leaf with 3 chunky brass hinges. | ||
+ | These are rebated into both pieces of wood for a flush finish. | ||
+ | |||
+ | Supporting Leg & Flap: | ||
+ | 670 X 230 X 18 Sapele faced plywood. This is attached to the bottom leaf by 2 brass hinges. It has a bolt at the bottom which engages with a brass bolt hole in the saloon floor. | ||
+ | The Flap is 290 X 300 X 18 and attached to the leg with two brass hinges. It has a brass latch to secure it against the leg when not in use. When deployed the flap supports the top leaf. | ||
+ | |||
+ | Bulkhead Flap: | ||
+ | 400 X 200 X 18 Sapele faced plywood. The edge which fixed to the bulkhead with 2 brass hinges is bevelled at 45 degrees so that the flap protrudes under the top leaf to support it. | ||
+ | |||
+ | The legs and flaps are shaped to give a pleasing appearance. | ||
+ | |||
+ | The Edge of both leafs (closest to the camera in the last picture) are raked away slightly perhaps by 50mm with a 50mm radius on the corner. |
Latest revision as of 16:38, 27 June 2018
The early Konsorts had a folding saloon table which folded flat against the saloon bulkhead. This allowed for a pull bed frame which could be made up into a double berth with the port side cushions.
Measurements in millimeters
Bulkhead fixing: 445 X 55 x 55 with an 24 X 18mm rebate on one edge to accommodate the bottom leaf. This piece of wood is attached to the saloon bulkhead by 3 bolts which go through to the heads.
Bottom Leaf: 1094 X 445 X 18. Sapele faced Plywood. This is attached to the bulkhead fixing by 2 chunky brass hinges. These are rebated into both pieces of wood for a flush finish.
Top Leaf: 1070 X 445 X 18 Sapele faced plywood. This is attached to the bottom leaf with 3 chunky brass hinges. These are rebated into both pieces of wood for a flush finish.
Supporting Leg & Flap: 670 X 230 X 18 Sapele faced plywood. This is attached to the bottom leaf by 2 brass hinges. It has a bolt at the bottom which engages with a brass bolt hole in the saloon floor. The Flap is 290 X 300 X 18 and attached to the leg with two brass hinges. It has a brass latch to secure it against the leg when not in use. When deployed the flap supports the top leaf.
Bulkhead Flap: 400 X 200 X 18 Sapele faced plywood. The edge which fixed to the bulkhead with 2 brass hinges is bevelled at 45 degrees so that the flap protrudes under the top leaf to support it.
The legs and flaps are shaped to give a pleasing appearance.
The Edge of both leafs (closest to the camera in the last picture) are raked away slightly perhaps by 50mm with a 50mm radius on the corner.